€ 41,31
Descriere
Mini Jack Meter is designed to control the switching on and off lighting and electrical equipment in your home. With a voltage of 220 - 240 V, this socket can support up to 2500W (resistance), 1200 W (incandescent), 700 W (engine) or 320 W fluorescent equipment.
For the counter function Mini Jack AN181 can detect up to 10485.75 kW / h and supports the power, voltage and current, and the detection of the power factor. It can also detect overloads during which she will turn off the relay and the LED blink until the power is removed and re-established.
Mini Jack Meter is a device compatible Z-Wave ™ is designed to work with all compatible networks Z-Wave ™.
Each Z-Wave module functions as a wireless repeater with other modules to ensure full coverage of your home.
FEATURES:
- Order a lamp or a remote device
- Module integrating taken directly from an electrical outlet and the load to be controlled
- ON / OFF function to control lights or appliances (no change)
- Measuring the power consumption of the connected load
- Automatic shutdown in case of overload
- Control of local support via integrated button
- Z-Wave technology More
- Reduced dimensions to pass almost unnoticed
- Status LEDs on the integrated button
- Z-Wave repeater function
TECHNICAL CHARACTERISTICS :
- Module Type: receiver Z-Wave
- Power: 230 V, 50 Hz
- Consumption: 0.6W
- Maximum power:
- Resistive Load: 2500W
- Bulb incandesence: 1200W
- CFL Bulb: 320W
- LED bulb (not dimmable): 320W
- Measurement accuracy:
- 0.03 ~ 0.1A: Error <2W
- 0.1 ~ 1A: error <3%
- 1 ~ 15A: error <1%
- Frequency: 868.42 Mhz
- Range: up to 70 m outdoors, up to 30 m in buildings
- Display: LED on the button
- dimensions:
- Length (including connector): 74mm
- Diameter: 52mm
Specificaţii
Primary Controller Compatibility | |
---|---|
1 eeDomus+ | Full Compatible |
Fibaro Home Center 2 v4.160 | Full Compatible |
Fibaro Home Center Lite v v.4.160 | Full Compatible |
Vera Edge / Plus / Secure | Full Compatible |
Zipabox/Zipaminicro/ZipaTile | Full Compatible |
Piper / Piper NV (v.1.7.1) | Full Compatible |
Indigo | Full Compatible |
jeedom | Full Compatible |
Z-Wave.me / Z-Way / PoPP Hub | Full Compatible |
Domoticz | Full Compatible |
OpenHAB | Full Compatible |
ZiHome | Full Compatible |
Tech Data | |
50 IP Rating | IP20 |
51 Power Supply | 230 V, 50 Hz |
52 Attachable Loads | Resistive: 2500W Incandescent: 1200W Fluocompact: 320W Non Dimmable Led Bulb: 320W |
53 Explorer Frames - NWI Support | Yes |
54 SDK | 6.51.02 |
55 App Version | |
56 Device Type | On/Off Power Switch |
57 Peper1 Database link | |
58 Z-Wave Alliance Product Link | http://products.z-wavealliance.org/products/1440 |
Procedures | |
90 Incluison | 1. Put the Z-Wave Controller into inclusion mode. 2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. |
91 Exclusion | 1. Put the Z-Wave Controller into exclusion mode. 2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. |
92 Factory Reset | 1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. 2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds). 3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes. 4. Use this procedure only in the event that the network primary controller is missing, or otherwise inoperable. |