-600x600.jpg "Releu cu contact de inalta putere(40A) cu masurarea consumului Aeon Labs(GEN5)")
€ 90,90
Descriere
Heavy Duty of Aeotec Smart Switch este un intrerupator care poate controla un dispozitiv sau un grup de dispozitive a carui putere de rupere este de maxim 9600.Dumneavoastra puteti controla in functie de programul predefinit sau automatizarea pe care o doriti.
Cu acest releu primiti instantaneu si informatii legate de consumul real de curent electric.Cu el puteti planifica si controla de mod automat pentru a reduce costurile pentru un dispozitiv care necesita pana la 40A de putere.
Z-Wave controller (remote dongle ...) is required to integrate this module in your network if you already have an existing network. Each Z-Wave module functions as a wireless repeater with other modules to ensure complete coverage of your home.
FEATURES:
- Order a device or group of high wattage appliance remotely
- ON / OFF function
- Measurement of the instantaneous and cumulative consumption
- Works with devices that require a maximum 40 amps of power
- Part of the range of Aeon Labs Gen5
- Safety radio communication via AES-128 Chip integrates Z-Wave 500 series
- Faster communication 250% compared to standard Z-Wave devices
- Supports frames exploration
- Z-Wave Beaming support Updates
- Firmware Over The Air (OTA) Repeater messages
- Z-Wave Optimization of the antenna, 150 meters range
- Ease of use and installation
SPECIFICATIONS:
- Module Type: Z-Wave Receiver
- Power supply: 240VAC, 50/60 Hz
- Consumption: 1W Maximum load: 9600W / 40A
- Frequency: 868.42 Mhz
- Transmission distance: 200m in open field
- IP Protection: IP43
- Dimensions: 150mm x 118mm x 35mm Weight: 350g
- Operating temperature: 5-40 ° C
- Operating Humidity: 80%
- Certifications: FCC, UL, CE, ROHS
Specificaţii
| Primary Controller Compatibility | |
|---|---|
| 1 eeDomus+ | full compatible |
| Fibaro Home Center 2 v4.160 | not tested |
| Fibaro Home Center Lite v v.4.160 | not tested |
| Vera Edge / Plus / Secure | not tested |
| Zipabox/Zipaminicro/ZipaTile | not tested |
| Piper / Piper NV (v.1.7.1) | not tested |
| Indigo | not tested |
| jeedom | not tested |
| Domoticz | not tested |
| ZiHome | not tested |
| 49 Vera 3 | not tested |
| 49 Vera Lite | not tested |
| Tech Data | |
| 50 IP Rating | IP43 |
| 51 FLiRS | |
| 51 Power Supply | 240VAC, 50/60 Hz |
| 52 Attachable Loads | 9600W / 40A |
| 53 Explorer Frames - NWI Support | |
| 54 SDK | |
| 55 App Version | |
| 56 Device Type | Slave with routing capabilities |
| 57 Peper1 Database link | http://pepper1.net/zwavedb/device/604 |
| 58 Z-Wave Alliance Product Link | http://products.z-wavealliance.org/products/1089 |
| 95 Generic Device Class | Binary Switch |
| 96 Specific Device Class | Binary Power Switch |
| 97 Routing | Yes |
| Procedures | |
| 90 Incluison | Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing. |
| 91 Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing. |
| 92 Factory Reset | Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. |
| 93 Wake Up | N/A |
