Universal Dimmer 250W Z-Wave+ Fibaro with metering

The in-wall micromodule FGD-212 by Fibaro  will allow you to control a lighting system thanks to the Z-Wave protocol while maintaining your existing switch. You will therefore be able to operate a connected lamp and to vary its intensity using the existing switch, or iva a Z-Wave transmitter.

The new dimmer Fibaro FGD-212 is equipped with a smart detection algorithm of the light source which facilitates the configuration and ensures a high compatibility of the device. It has a self-protection against overloading and a soft start function. In the case of non-dimmable light sources, only the ON / OFF function is possible (connection with 3 wires system).

It is compatible with any type of lamps dimmables or not:

As a dimmer: -

• Classic Light Sources Incandescent and halogen powered by 230VAC
• 12V halogen lamps (with electronic transformers)
• 12V halogen lamps (with ferromagnetic transformers)
• LED Lamps dimmables
•  Fluorescent Lamps CFL dimmables
•  Using the Bypass with a source of dimmable light up in  225VA 2 wires mode connection (depending on load type)

As an On/off switch:

• Fluorescent lamps
• LED Lamps
• Using the Bypass module with any light source its supports up to 225VA (depending on load type)

This module  can be used in 2 wires mode  (without neutral), replacing an existing switch, or three wires mode with a conventional power supply (phase + neutral). For lamps with very low power consumption (LED lamp, for example), you can use the Bypass moduel load  Fibaro FGB-001 that allows proper operation of the module.

In addition to the function variation, this micro-module can also measure the power consumption of the connected load. Instant consumption figures (in W) and total electricity consumption (kWh) can be consulted.

A Z-Wave controller (remote, control dongle, gateway ...) is necessary to integrate this module in your Z-Wave . Each Z-Wave module functions as a wireless repeater with other modules to ensure full coverage of your home.

FEATURES:

• Youo can manage a lighting system locally and in remote
• Module can be installedbehind an existing switch
• ON / OFF function and dimmer
•  Use 2 wires mode neutral not required)
• Integrates Z-Wave chip 500 series
• Communication 250% faster compared to standard Z-Wave devices
• Automatic load detection
• Protected against overload
• Compatible with Z-Wave and  Z-Wave Pluscontrollers
• Function Measuring Active Power and Energy
• Works with different types of switches - tappet, rocker, three-way, etc.
• Soft start function (soft-start)
• LED status indication of inclusion, and calibration levels
• Z-Wave range tester integrated
• Automatically detects wiring faults, high temperature, power surges and overloads
• Advanced Configuration Options
• Small, discreet and aesthetic
• Ease of use and installation

SPECIFICATIONS:

• Module Type: receiver Z-Wave
• Power supply: 230V +/- 10%, 50Hz
• Consumption: 1.3W
• Wiring: neutral not required
• Load capacity: 50-250W (resistive load) or 0.25-1.1A (inductive load)
• Lamp type  compatible (dimmable): Incandescent, CFL, Halogen (230VAC and 12VDC with electronic transformer), LED
• Lamp type compatible (not dimmable): CFL, LED
• Frequency: 868.42 Mhz
• Signal strength: 1mW
• Transmission distance: 50m free field, 30m indoor
• Dimensions: 42.5 x 38.25 x 20.3mm
• Operating temperature: 0-35 ° C
• Temperature limit: 105 ° C
• Standards: RoHS 2011/65 / EU, LVD 2006/95 / EC, EMC 2004/108 / EC R & TTE 1999/5 / EC

Manual:

​

Spune-ţi opinia

Introduceţi codul din imagine: