-600x600.jpg "Motion sensor Outdoor Z-Wave Plus Square Insert - Philio")
€ 49,58
Descriere
This compact ball-shaped sensor recognizes movement at a distance of up to 8 meters and can be easily installed on the ceiling or on a wall thanks to its flush mount.
You can place it near your lighting and thus automate your lights. In addition, this sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside.
The sensor is battery powered and can be easily added to your Z-Wave home automation system. A Z-Wave controller (remote control, dongle, home automation box, ...) is necessary to integrate this detector into your network if you already have an existing network.
FUNCTIONS:
- Motion Detector Z-Wave Plus
- Z-Wave 500 Series chip enables multichannel operation and higher throughput (9.6 / 40 / 100kbps)
- Button to include / exclude detector
- Low battery detection
- Very small, small dimensions
- OTA firmware update
- Low power consumption (battery life of about 3 years)
- Easy installation thanks to its flush-mounting bracket
- Use indoors or outdoors
TECHNICAL CHARACTERISTICS :
- Type: Z-Wave Plus Transmitter (868.42MHz)
- Power supply: Lithium battery CR123A 1700mA
- Operating Voltage: 3V
- Operating Current: 33mA
- Standby Power: 30uA
- Battery life: 3 years
- Operating Temperature Range: -10 ° C to + 40 ° C
- Frequency: 868.42 Mhz
- Radio range: 100m in open field, 40m indoors
- PIR detection range: 8m, 4m to 360 °
- Mounting Diameter: 7cm
- Certifications: EMC 2004/108 / EC, R & TTE 1995/5 / EC, LVD 2006/95 / EC, FCC Part 15
Manual:
Specificaţii
| Primary Controller Compatibility | |
|---|---|
| 1 eeDomus+ | Full Comtible |
| Fibaro Home Center 2 v4.160 | Full Comtible |
| Fibaro Home Center Lite v v.4.160 | Full Comtible |
| Vera Edge / Plus / Secure | Not Tested |
| Zipabox/Zipaminicro/ZipaTile | Full Comtible |
| Piper / Piper NV (v.1.7.1) | Not Tested |
| Indigo | Not Tested |
| jeedom | Full Compatible |
| Z-Wave.me / Z-Way / PoPP Hub v 3.2.1 | Not Tested |
| Domoticz | Not Tested |
| ZiHome | Not Tested |
| Tech Data | |
| 51 FLiRS | No |
| 51 Power Supply | Battery CR123 |
| 53 Explorer Frames - NWI Support | No |
| 54 SDK | 6.51.09 |
| 55 App Version | 1.27:01.21 |
| 56 Device Type | Notification Sensor |
| 58 Z-Wave Alliance Product Link | https://products.z-wavealliance.org/products/2002 |
| Procedures | |
| 90 Incluison | There is a button on PSP05. 1. Have Z-Wave™ Controller entered inclusion mode. 2. Pressing button once to enter the inclusion mode. 3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds. |
| 91 Exclusion | There is a button on PSP05. 1. Have Z-Wave™ Controller entered exclusion mode. 2. Pressing button once to enter the exclusion mode. |
| 92 Factory Reset | There is a button on PSP05. 1. Pressing button for about 5 seconds. 2. IDs are excluded and all settings will reset to factory default. Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable. |
| 93 Wake Up | There is a button on PSP05. Press the button once, the device will awake 10 seconds. |
