4 Buttons rechargeable Remote Z-Wave Plus - Hank

28,88

Disponibilitate:
În Stoc
Cod produs:
ES-72-HAN-HKZW-SCN04
Producător:
Hank

Not yet rated
Spune-ţi opinia

Descriere

The Hank Z-Wave Plus Scene Controller is a wireless, portable and rechargeable device. It can control Z-Wave devices, such as a smart plug or intelligent dimmer after being included in a Z-Wave controller. You can also use it to activate scenes. This stage controller can perform 3 different actions per button, depending on the type of support: short press, support maintained, support released. Operating with a rechargeable battery with a range of 3 to 6 months, it will be very easy to recharge by connecting a USB cable on its micro-USB port. No need to change the batteries! In addition, this stage controller is equipped with a buzzer that will alert when the battery is low (less than 20%), or when communication has failed. An RGB LED is present to give visual information.

This stage controller is also equipped with the Z-Wave scope test function. A Z-Wave controller (remote control, dongle ...) is required to integrate this module into your network if you already have an existing network. ç

FUNCTIONS:

  • Z-Wave + Scene Controller
  • Control up to 3 devices / scenes per button
  • Z-Wave Range Test Function
  • Rechargeable battery
  • Low battery warning and communication error (via buzzer)
  • Security of radio communication via AES-128 encryption
  • Integrates the Z-Wave 500 series chip
  • Firmware Updates Over The Air (OTA)
  • Ease of use and installation

  TECHNICAL CHARACTERISTICS :

  • Module Type: Z-Wave + 500 Series Transmitter
  • Power supply: 3,6V rechargeable battery LIR2450
  • Standby power consumption: 3uA
  • Power consumption in operation: 36mA
  • Frequency: 868.42 Mhz
  • Transmission distance: 100m in free field, 30m indoors
  • Dimensions: 50 x 50 x16 mm
  • Operating temperature: 0 ° C to 40 ° C
  • Certifications: FCC, CE, Z-Wave
  • Z-Wave certification number: ZC10-16095219

Manual:

Specificaţii

Primary Controller Compatibility
1 eeDomus+ Full Compatible
Fibaro Home Center 2 v4.160 Not Tested
3 Fibaro Home Center Lite v v.4.160 Not Tested
4 Vera Edge / Plus Not Tested
5 Zipabox/Zipamini/ZipaTile Not Tested
6 Piper / Piper NV (v.1.7.1) Not Tested
Indigo Not Tested
8 jeedom Full Compatible
Z-Wave.me / Z-Way / PoPP Hub Not Tested
10 Domoticz Not Tested
ZiHome Not Tested
Somfy Tahoma Not Tested
Home Assistant Not Tested
Telldus Not Tested
Tech Data
50 IP Rating IP20
51 FLiRS No
51 Power Supply Batterie rechargeable 3,6V LIR2450
53 Explorer Frames - NWI Support No
54 SDK 6.51.08
55 App Version HW: 1 FW: 1.00
56 Device Type Wall Controller
58 Z-Wave Alliance Product Link https://products.z-wavealliance.org/products/1968
Procedures
90 Incluison Included as non-secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Waave network controller operating manul). 3. Triple click a button. 4. If the inclusion is successful, the LED will blink in blue less than for 5 seconds and then keep on for 15 seconds. Included as a secure device: 1. Insert the LIR2450 battery. 2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual). 3. Pressing and holding a button for 3 seconds. 4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds.
91 Exclusion To remove the Scene Controller from the Z-Wave network: (1) Insert the LIR2450 battery. (2) Set the Z-Wave network main controller into remove mode (see Z-Wave controller operating manual). (3) Triple click the a button, if the exclusion is successful, LED will blink in orange for less than 5 seconds and then keep on for 3 seconds.
92 Factory Reset Pressing and holding a button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds. Using this procedure only in the event that the network primary controller is missing or otherwise inoperable.
93 Wake Up Pressing and holding a button for 3 seconds. Led will turn to green, which means Scene Controller has been woken up.

Opinii (0)

Spune-ţi opinia

Notă: Codul HTML este citit ca şi text!

Rău            Bun


Continuare

Z-Wave Romania

The On-line shop for home automation Z-Wave products. Based in Spain, we deliver all over the world. Z-Wave is the international standard for wireless networking of home control systems. You can manage lighting, electricity, blinds, alarms etc ... Z-Wave products from different vendors work well together allowing control of smart home.

Contact Us

+34600612889
+34600612889
danyvizariu@gmail.com
danyvizariu@gmail.com
danyvizariu
danyvizariu

Facebook